Installation Requirements
-
Phillips screwdriver (for rack- or wall-mounting)
-
Standard-sized, 19" wide rack with a minimum of 1U height available (for rack-mounting)
-
Use compatible fiber SFP modules with the appropriate fiber optic cabling. For information about compatible fiber SFP modules, visit: ubnt.link/SFP_DAC_Compatibility
-
For indoor applications, use Category 5 (or above) UTP cabling approved for indoor use.
-
For outdoor applications, shielded Category 5 (or above) cabling should be used for all wired Ethernet connections and should be grounded through the AC ground of the power supply.
We recommend that you protect your networks from harmful outdoor environments and destructive ESD events with industrial-grade, shielded Ethernet cable from Ubiquiti. For more details, visit: ui.com/toughcable
|
System LED |
|||
|---|---|---|---|
|
Flashing White |
Bootup in progress. |
||
|
White |
Ready for use, not connected to Ubiquiti® Network Management System (UNMS™). |
||
|
Blue |
Ready for use, connected to UNMS. |
||
|
Steady Blue with Occasional Flashing |
Ready for use, unable to connect to UNMS, check connection to UNMS server. |
||
|
Quickly Flashing Blue |
Used to locate a device in UNMS. |
||
|
Alternating |
Firmware upgrade in progress. |
||
|
SFP Speed/Link/Act LED (Ports 1 - 12) |
|||
|
Off |
No Link |
||
|
Amber |
Link Established at 100 Mbps Flashing Indicates Activity |
||
|
Green |
Link Established at 1000 Mbps (1 Gbps) Flashing Indicates Activity |
||
|
RJ45 Speed/Link/Act LED (Ports 13 - 16) |
|||
|
Off |
No Link |
||
|
Amber |
Link Established at 10/100 Mbps Flashing Indicates Activity |
||
|
Green |
Link Established at 1000 Mbps (1 Gbps) Flashing Indicates Activity |
||
|
SFP (Ports 1 - 12) |
|||
|
Hot-swappable SFP ports support 1 Gbps connections. Ports 1-8 also support 100 Mbps. |
|||
|
RJ45 (Ports 13 - 16) |
|||
|
RJ45 ports support 10/100/1000 Ethernet connections. |
|||
|
Reset Button |
|||
|
There are two methods to reset the EdgeSwitch to factory defaults: Runtime Reset (Recommended) The EdgeSwitch should be running after bootup is complete, and the System LED is white. Press and hold the Reset button. The EdgeSwitch will reboot, and the System LED becomes blue after three seconds. Continue to hold the Reset button for about 15 seconds until the System LED flashes blue for two seconds. This indicates that the EdgeSwitch has reset to its factory defaults. Power-on Reset
|
|||
|
Console |
|||
|
RJ45 serial console port for Command Line Interface (CLI) management. Use an RJ45-to-DB9, serial console cable, also known as a rollover cable, to connect the Console port to your computer. Then configure the following settings as needed:
|
|||
|
DC Input |
|||
|
The 25VDC input can connect a redundant or stand-alone DC power source (not included) with minimum power: 56W, 25 to 16V, and 2.5 mm DC power inline connector.
|
|||
|
Power |
|||
|
Connect the included Power Cord to the Power port. |
|||
Specifications
|
ES-12F |
|
|
Dimensions |
443 x 221 x 43 mm (17.44 x 8.70 x 1.69") |
|---|---|
|
Weight |
|
|
Rack-Mount Brackets Included |
2.68 kg (5.91 lb) |
|
Rack-Mount Brackets Excluded |
2.59 kg (5.71 lb) |
|
Total Non-Blocking Line Rate |
16 Gbps |
|
Max. AC Power Consumption |
56W |
|
Power Method |
|
|
AC |
100-240VAC/50-60 Hz, Universal Input |
|
DC |
DC 56W, 25 to 16V, with 2.5 mm |
|
Power Supply |
AC/DC, Internal, 56W DC |
|
Supported Voltage Range |
100 to 240VAC 25 to 16VDC |
|
LEDs Per Data Port |
Speed/Link/Activity |
|
Interfaces |
|
|
Networking Interfaces |
(8) 100/1000 Mbps SFP Ethernet Ports |
|
Management Interface |
(1) RJ45 Serial Port Out-of-Band, Ethernet In-Band |
|
Rackmount |
Yes, 1U High |
|
ESD/EMP Protection |
Air: ± 24 kV, Contact: ± 24 kV |
|
Shock and Vibration |
ETSI300-019-1.4 Standard |
|
Operating Temperature |
-5 to 40° C (23 to 104° F) |
|
Operating Humidity |
5 to 95% Noncondensing |
|
Certifications |
CE, FCC, IC |
